The Most Popular Peugeot Keys The Gurus Are Using Three Things

Peugeot 208 Key Replacement It is recommended to leave the replacement of Peugeot keys for 208 to auto locksmiths with the equipment and skills. They will be able to create and program new keys faster than a dealership would and at a lesser cost. A dead coin battery is most likely to be at fault the reason why your key fob isn't locking or unlocking doors. There are other reasons that the key might be malfunctioning. Dead Coin Battery A dead coin battery will stop your Peugeot 208 from locking and unlocking, and also stopping it from starting the engine. If this is the scenario, you'll need utilize the backup starting method that is described in the owner's manual to your vehicle. The spark plugs could also be worn out. The spark plugs are responsible for igniting the fuel that starts the engine. However, they have a limited life span. If they aren't utilized enough, they will eventually fail. There is a straightforward solution to this problem. The best thing to do is to determine the voltage of your car battery with a multimeter. If the voltage falls below 11,5 volts, it's the time to replace it. It is also necessary to clean the contacts of the battery in the event that it is damaged by corrosion. This can be done by removing the rubber covers from the two battery terminals and then using a wirebrush, you can remove any parts of the battery that are corroded. After that, you need to connect the positive and negative pole cables. Water Damage If your 208 doesn't start and the battery has not gone flat, you should examine the spark plugs. You might find that they are simply too dirty and they don't spark. This can be fixed easily by cleaning the spark plugs in an workshop. Peugeot cars are equipped with a transponder style key that works with the car's ignition system. This makes sure that only the correct key is able to turn the engine. If the chip inside the Peugeot key is damaged, then it will not send the proper signal to the vehicle. This is a frequent issue that can occur due to water damage. This is most common in colder climates. the vehicle could have been exposed to snow or rain. If this is the case, get in touch with a reputable locksmith who has all of the tools and equipment needed to reprogram the new key. They also have the most up-to-date technology and equipment needed to make a Peugeot 208 smart key. The process shouldn't last more than 15 minutes. Contacts to the battery are not working properly. Peugeot replaced the old transponder chips with a new model that is based on electronic components that are mounted on a circuitboard. The new system is fantastic in its initial state, but the circuit boards wear out over time and stop working properly. This can prevent the immobiliser from working, so your vehicle won't be able to start. If this is the case it's recommended to get in touch with a Peugeot specialist or locksmith. A common issue is when the battery in the key fob starts to die. This causes the blade of the key to stop feeding into the lock. A car locksmith can replace the battery and cut a fresh blade for you, it's generally a quick fix. Faulty Receiver Module It could be that the receiver module has a problem If your Peugeot key fob fails to function after being dropped on the floor, or exposed to a sudden storm or accidentally washed. The receiver module is responsible for transmitting radio signals to the onboard computer that manages the central locking system of your Peugeot vehicle. The rubber seals on the key fob prevent water from getting to the electronic chip. Water can damage the chip when it is exposed to water for long periods of time. The high salt content in the ocean or pool could cause damage to the key fob when it is submerged. If your Peugeot spare key fob stops working, you'll need to have the module replaced. This can only be completed by an experienced auto locksmith or Peugeot specialist. As opposed to other cars, Peugeot keys are protected by an exclusive immobilizer system that requires the correct programming for the start of the engine. This is why it is imperative that you should only rely on an authorized Peugeot locksmith to create and program the replacement. Computers with faulty on-board computers The on-board computer of your Peugeot is responsible many features in your car, including power windows and airbags. The on-board computer will show a code when something goes wrong. This code will be saved within the system until the issue is resolved. Most often, this involves replacing the onboard computer. One of the most common reasons for the airbag light flashing is loose or corroded connections in the airbag sensor. This can be caused by wear and tear, aging, or exposure to salt and moisture. It is important to have this issue addressed as quickly as possible, since an airbag that is malfunctioning can be dangerous in the event of an accident. If G28CarKeys is showing a card not detected error, then the battery inside the key fob could be dead or weak. This will stop the key fob sending a signal to disarm your vehicle's immobilizer. You can test this by pressing the unlock button on the key fob, then attempting to start your car. If this does not work then the battery in the key must be replaced.